Effect of Interrupted Cutting of Variable Loading on Cutting Tool
Keywords:
interrupted cutting, variable loading, tool wear, tangential cutting forceAbstract
Cutting tools are used in various processes at very different conditions including material behaviors, machining parameters, geometry, and tribological characteristics. For an efficient machining, a cutting tool requires high hardness, high chemical stability, and high wear resistance. Machining can be more challenging in the interrupted cutting due to the alteration in mechanical and thermal loads. When interrupted surfaces are machined, the tool also requires sufficient impact and fatigue resistances. The main goal of this work to investigate the effect of interrupted cutting of variable loading when turning AISI 4140. Based on the experimental results, the main conclusion of this work was the tool life was shorter in the interrupted turning experiments. Although lower tangential cutting forces were measured in the interrupted cutting tests, the intervals deteriorated the tool life. The trends of the tangential cutting forces were observed as expected in the continuous turning at dynamic loading whereas the trends were different and not as expected in the interrupted turning. In both continuous and interrupted turning at dynamic loading, abrasive wear was the major mechanism on the flank surface.
References
[2] Saglam, H., Unsacar, F., Yaldiz, S. (2006). Investigation of the effect of rake angle and approaching angle on main cutting force and tool tip temperature. International Journal of Machine Tools and Manufacture, 46(2), 132-141.
[3] Günay, M., Aslan, E., Korkut, İ., Şeker, U. (2004). Investigation of the effect of rake angle on main cutting force. International Journal of Machine Tools and Manufacture, 44(9), 953-959.
[4] Senthil Kumar, A., Raja Durai, A., Sornakumar, T. (2006). The effect of tool wear on tool life of alumina-based ceramic cutting tools while machining hardened martensitic stainless steel. Journal of Materials Processing Technology, 173(2), 151-156.
[5] Korkut, I., Donertas, M.A. (2007). The influence of feed rate and cutting speed on the cutting forces, surface roughness and tool–chip contact length during face milling. Materials & Design, 28(1), 308-312.
[6] Diniz, A.E., Gomes, D.M., Braghini Jr, A. (2005). Turning of hardened steel with interrupted and semi-interrupted cutting. Journal of Materials Processing Technology, 159(2), 240-248.
[7] Chandrasekaran, H., Thoors, H. (1994). Tribology in interrupted machining: role of interruption cycle and work material. Wear, 179(1-2), 83-88.
[8] Grzesik, W. (2008). Influence of tool wear on surface roughness in hard turning using differently shaped ceramic tools. Wear, 265, 327–335.
[9] Diniz, A.E., Oliveira, A.J., (2008). Hard turning of interrupted surfaces using CBN tools. Journal of Materials Processing Technology, 195, 275–281.
[10] A. de Godoy, V. A., Diniz, A.E. (2011). Turning of interrupted and continuous hardened steel surfaces using ceramic and CBN cutting tools. Journal of Materials Processing Technology, 211, 1014–1025
[11] José de Oliveira, A., Diniz, A.E., Ursolino, D.J. (2009). Hard turning in continuous and interrupted cut with PCBN and whisker-reinforced cutting tools. Journal of Materials Processing Technology, 209, 5262–5270.
[12] Chou, Y.K. Evans, C.J. (1999). Cubic boron nitride tool wear in interrupted hard cutting. Wear, 225–229, 234–245
[13] Pavel, R. Marinescu, I. Deis, M., Pillar, J. (2005). Effect of tool wear on surface finish for a case of continuous and interrupted hard turning. Journal of Materials Processing Technology, 170, 341–349
[14] Sayit, E., Aslantas, K., Çiçek, Ç. (2009). Tool Wear Mechanism in Interrupted Cutting Conditions. Materials and Manufacturing Processes, 24(4), 476-483
[15] International Organization for Standardization, (1993). Tool-life testing with single-point turning tools, ISO 3685
[16] Trent, E.M., Wright, P.K., (2000). Metal Cutting, fourth ed. Butterworth-Heinemann, Oxford.
Downloads
Published
Issue
Section
License
Bánki Közlemények is loyal to open access for academic work. All the original articles and review papers published in this journal are free to access immediately from the date of publication. We don’t charge any fees for any reader to download articles and reviews for their own scholarly use.
The Bánki Közlemények also operates under the Creative Commons Licence CC-BY-NC-ND. This allows for the reproduction of articles, free of charge, for non-commercial use only and with the appropriate citation information. All authors publishing with the Bánki Közlemények accept these as the terms of publication.
